EverFocus Eptz3000 Manuel d'utilisateur

Speed Dome EPTZ3000/EPTZ3000I USER MANUAL Date: Feb15, 2006

1-91.3.3. EPTZ3000/EPTZ3000I Control Board The PCB board with two dipswitches is the control board of EPTZ3000/EPTZ3000I. The two switches are u

1-101.4. EPTZ3000/EPTZ3000I Connection Alarm 1Alarm 4Alarm 3Alarm 2GROUNDRS485 Tx(+)RS485 Tx(-)24V AC110V ACVideo OutPOWER24V AC / 3.5 ABNC1.0Vpp ± 0

1-111.5. EPTZ3000/EPTZ3000I Quick Operation Guide (Work with EKB500) EPTZ3000/EPTZ3000I and EKB500 (Keyboard) can work together by using factory defa

2-122. EPTZ3000/EPTZ3000I INSTALLATION 2.1. Packing List There are 3 boxes that are housing, bulb and mechanical part with a camera module, one wall

2-13Video Cable A BNC cable is used for connecting an EPTZ3000/EPTZ3000I to a DVR or a monitor. An amplifier may be needed if the video cable is too

2-142.3.1. Address Setting The address code of the EPTZ3000/EPTZ3000I should be set to correspond properly with a control device to control multiple

2-15ON12345678Switch Address1ON123456782ON123456783ON123456784ON123456785ON123456786ON123456787ON123456788ON123456789ON1234567810ON1234567811ON123456

2-16ON12345678Switch Address129ON12345678130ON12345678131ON12345678132ON12345678133ON12345678134ON12345678135ON12345678136ON12345678137ON12345678138O

2-172.3.2. Communication Protocol Setting The 1st, 2nd and 3rd bits of the SW2 are used to set communication protocol. The factory default protoco

2-18Notice: Please make sure the power is off before setting, and restart the EPTZ3000/EPTZ3000I to enable a new value after changing. 2.3.4. RS-48

1-1Table of Contents 1. EPTZ3000/EPTZ3000I OVERVIEW... 1-3 1.1. Introduction ...

2-192.4. Rack and Speed Dome Installation 2.4.1. Installation Requirements 1. Installation should be handled by a qualified service agent and should

2-202. Thread the cable through the hole in the wall mount bracket, and screw in 4 M8 nuts for mounting the bracket. 3. Take off the housing from

2-215. Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing, and twist the mechanical part clockwi

2-22 Notice: In order to protect the bulb from dirt and scrape, please put on the gloves before installing the bulb. 7. Turn on the power, and start

2-23RELAYJP5Video +Video -RS485 +RS485 -AC24AC24Cut the ceiling Notice: Please notice the polarity of control line. The EPTZ3000I will not work if t

2-24 Notice: The camera module on the mechanical part is very sensitive. Please be careful when installing this part. 7. Remove the lens protection

2-252.5. Accessories 2.5.1. EPTZ-CPMA: Ceiling Pendant Mount Adapter The pole mount is used for installing a speed dome on the ceil

2-262.5.3. EPTZ- CMA: Corner Mount Adapter The corner mount are used for installing a wall mount bracket to a 270° corner of walls indoors or

3-273. EPTZ3000/EPTZ3000I CAMERA SETUP MENU In this section, setup and operation guide of EPTZ3000/EPTZ3000I will be introduced. There are 18 items

3-28 3.1.1. Camera Setup Menu Press MENU to enter camera setup menu. Press Shift + Joystick up/down to change subentries, and right/left to change t

1-22.5.3. EPTZ- CMA: Corner Mount Adapter...2-26 3. EPTZ3000/EPTZ3000I CAMERA SETUP MENU...

3-296. WBC MODE: White balance control mode. AUTO: Auto white balance compensation. 2000K: Manual white balance compensation in 2000K color temperatu

3-30 11. ALM-IN4 SET： The status of input alarm 4. N.O.: Enable a normal open alarm input. N.C.: Enable a normal close alarm input. OFF: Disable

3-311/60 (NTSC) and 1/50 (PAL): default manual shutter; 1/160: 1/160 sec shutter for both NTSC and PAL 1/250: 1/250 sec shutter for both NTSC and PAL

3-32can set the masking size and position in the private zone setup mode. In this mode, you can press “Shift” + “6” to increase masking horizontal si

3-33 23. LOAD DEFAULT： Load default setting. Select this item, and then press “Enter” to load default setting. Press “Clr” + “Menu” whenever you wan

4-344. EPTZ3000/3000I FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode  Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockw

4-35  Preset a position: Shift the Joystick to the position you would like to preset, and then press Shift + Position. The system will ask you to e

4-36 To-and-fro tour mode: Press Shift + Tour to run a to-and-fro tour. The system will ask you to enter the tour number you would like to run, and

4-37RELAYJP6JP4JP3 JP1JP5Video +Video -RS485 +RS485 -AC24AC24JP51 ~ 9APPENDIX : The Alarm I/O Connection There are 4 alarm inputs and 1 a

4-38 P/N: MW01G0070B EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan T

1-31. EPTZ3000/EPTZ3000I OVERVIEW 1.1. Introduction EPTZ3000/EPTZ3000I, an intelligent high-speed dome camera is ready to secure your property with

1-4Furthermore, the micro control unit enables camera a nimble and exact movement from minimal 0.01°/sec to maximal 360°/sec. It can go to every pres

1-51.2. Specifications Model EPTZ3000 (outdoor) EPTZ3000I (indoor) Power Supply AC 24V Power consumption 70W with heater 18W without heater Ope

1-6Communication RS-485 Address editable Yes (through DIP switch) Speed Dome Address 0-255 Manual Pan/tilt speed Pan: 0.01º ~ 360º/s ; Tilt: 0.01

1-71.3. Feature 1.3.1. Profile of EPTZ3000/EPTZ3000I Wall Mount BracketHousingInner HousingM5 Bolt (Hex) x3M3 Bolt x3BNC CablePower CableRS485 Cabl

1-81.3.2. EPTZ3000/EPTZ3000I Base Board The base board that is on the bottom of the housing connects to power cable, video cable, control cable,